Balustrade Methods

At Miami Stainless we have several stainless steel wire balustrade methods available. From our simple DIY hand swaged balustrade methods to the more professional looking streamline balustrade methods we can find a system that will best suit your needs. We have a huge selection of quality stainless steel fittings in stock meaning goods are almost always dispatched the same day they are ordered. We provide a full in house swaging service with very quick turnaround times (usually 1-2 days). If you need any help or advice you can call one of our friendly staff on 1800 022 122, or you can fax (1800 022 199) or email us a plan of your balustrade and we will contact you with recommendations or a quote. Most wire balustrade methods can be easily adapted to suit timber or steel posts.

  Click on the pictures below to view our most popular methods in more detail

Nutsert Tension Rod System: All in all this is one of the most stylish systems currently available in the marketplace. Ideally suited to straight balustrade runs you will undoubtedly be more than satisfied with the end result. This system can be slightly more time consuming to install due to the requirement of on-site hand swaging, however this is made up through the savings made from the non requirement of factory hydraulic swaging.

Please Note: This method is only suitable for metal posts.

FAQ About This System  

Can I install this method myself? Yes, even someone with no experience can easily install all our systems.

Do I need any special tools? Other than common handyman tools you will need a nutsert insert tool ($260 + GST), hex hand swaging tool ($65 + GST), soft jaw pliers ($13.95), and a set of wire rope cutters ($19.80). You can also purchase a Hex drive bit for easy insertion of the threaded inserts.

What size and type of wire do I use? This method is almost always used with 3.2mm 1 x 19 stainless steel wire; this wire is the sleekest and is more than strong enough for a balustrade.

What spacing do I need between my wires? When using 3.2mm 1 x 19 wire you will usually need 80mm spacing (11 runs) between your wires. Please click here for more information on wire balustrade regulations.

What size pilot hole should I drill for my Nutserts? You will need a 11mm hole on the inside face of each termination post to suit 8mm nutserts.

What is the maximum length run I can do? Up to around 8-10metres. Longer runs can be achieved by using a tensioning system at both ends.

What size hole should I drill through my posts? A 4.0mm hole through your intermediate posts will allow the 3.2mm wire rope to easily fit through. Please note: If you are using grommets the drill size will need to be 11/32" in to each side of your intermediate post.

Can I take my wire around corners? No you cannot bend this system around corners.

Can I use this method if I have steel posts? Yes.

Can I use this method if I have timber posts? No, see the insert tension rod system if you have timber posts.

What do I need to get a quote? To get a free no obligation quote you will need to let us know how many and how long each section of your balustrade is. We will also need the distance between your decking and the underside of your handrail, so we can work out how many runs of wire you will need. You can either email us at info@miamistainless.com.au, call us on 1800 022 122, or fax us at 1800 022 199.

How do I order? If you know exactly what you require or you have obtained a quote from Miami Stainless simply contact us with a confirmation of your order. At this time we will require payment for your order, this can be done by either credit card over the phone (do not email credit card details) You can also deposit the funds in to our bank account once we have given you the total (please fax or email payment confirmation).

How much will freight cost me and when can I expect delivery? This method is usually dispatched within 1-2 days after payment. Miami Stainless has a maximum freight charge of $12(+gst) Australia wide. Please note: This does not include Air freight.

Delivery Times: Approximate only. For an exact delivery time please contact us on 1800 022 122.

QLD, ACT, & NSW: 1-2 working days  VIC & SA: 2-3 working days  TAS: 5-6 working days  NT & WA: 6-7 working days

What should I do if I have any further questions? If you have any further questions please contact Miami Stainless on 1800 022 122 or at info@miamistainless.com.au and one of our friendly staff will be happy to help you.

Over 300 Product Lines - Download Complete Catalogue (1.3mb)

Within Australia Free Call : 1800 022 122 - or email: info@miamistainless.com.au