Balustrade Methods

At Miami Stainless we have several stainless steel wire balustrade methods available. From our simple DIY hand swaged balustrade methods to the more professional looking streamline balustrade methods we can find a system that will best suit your needs. We have a huge selection of quality stainless steel fittings in stock meaning goods are almost always dispatched the same day they are ordered. We provide a full in house swaging service with very quick turnaround times (usually 1-2 days). If you need any help or advice you can call one of our friendly staff on 1800 022 122, or you can fax (1800 022 199) or email us a plan of your balustrade and we will contact you with recommendations or a quote. Most wire balustrade methods can be easily adapted to suit timber or steel posts.

  Click on the pictures below to view our most popular methods in more detail

The Streamline Lag Screw Swage Stud Method is ideal for those looking for an extremely slimline look. Your wires will arrive pre-assembled to your exact measurements meaning an extremely quick and simple installation, as well as a stylish finish. Tensioning of this method is achieved by the left and right hand threaded lag screws being turned into your timber posts. This method is only suitable for timber posts and  is more suitable for short runs. All fittings and wire in this method are 316 (marine) grade stainless steel.

Please Note: This method is only suitable for timber posts.

FAQ About This Method  

Can I install this method myself? Yes; even someone with no experience can easily install all our methods.

Do I need any special tools? Because this method arrives to you pre-made from our factory you will only require common handyman tools.

What size and type of wire do I use? This method is almost always used with 3.2mm 1 x 19 stainless steel wire; this wire is the sleekest and is more than strong enough for a balustrade.

What spacing do I need between my wires? When using 3.2mm 1 x 19 wire you will usually need 80mm spacing (11 runs) between your wires. Please click here for more information on wire balustrade regulations.

What is the maximum length run I can do? Around 7-8 metres is the maximum length you can acieve using the Lag Screw method.

What size pilot hole should I drill for my Lag Screws? 4mm; you can also choose to purchase an extra left and right hand threaded lag screw to pre cut a thread in to your posts.

What size hole should I drill through my posts? A 7.5mm hole through your intermediate posts will allow the lag screws to fit through. Please note: If you are using grommets the drill size will need to be 11/32" at least 10mm in to each side of your intermediate post.

Can I take my wire around corners? Miami Stainless highly recommends that you do not bend your wire around corners; this can fatigue the wire, put excessive stress on your posts, and make it difficult to get the required tension on your wire.

Can I use this method if I have timber posts? Yes.

Can I use this method if I have steel posts? No.

What do I need to get a quote? To get a free no obligation quote you will need to let us know how many and how long each section of your balustrade is. We will also need the distance between your decking and the underside of your handrail, so we can work out how many runs of wire you will need. You can either email us at info@miamistainless.com.au, call us on 1800 022 122, or fax us at 1800 022 199.

How do I order? When you come to order your balustrade we will need you to email or fax us with your exact measurements from the inside to inside face of your posts. At this time we will require payment for your order, this can be done by either credit card over the phone (do not email credit card details). You can also deposit the funds in to our bank account once we have given you the total (please email or fax payment confirmation)

How much will freight cost me and when can I expect delivery? This method is usually dispatched within 1-2 days after payment. Miami Stainless has a maximum freight charge of $12(+gst) Australia wide. Please note: This does not include Air freight.

Delivery Times: Approximate only. For an exact delivery time please contact us on 1800 022 122.

QLD, ACT, & NSW: 1-2 working days  VIC & SA: 2-3 working days  TAS: 5-6 working days  NT & WA: 6-7 working days

  What should I do if I have any further questions? If you have any further questions please contact Miami Stainless on 1800 022 122 or at info@miamistainless.com.au and one of our friendly staff will be happy to help you.

Over 300 Product Lines - Download Complete Catalogue (1.3mb)

Within Australia Free Call : 1800 022 122 - or email: info@miamistainless.com.au